PRV Audio

2x PRV 240W Shallow Super Tweeter Neodymium TW400Ti-Nd-4 SLIM 4 Ohm 3″ Rounded

  • Beitrags-Autor:
  • Beitrags-Kategorie:
  • Beitrags-Kommentare:0 Kommentare

Compact Neodymium Bullet Super TweeterIncludes: PAIR of Tweeters - Model: TW400Ti-Nd-4 SLIM The PRV Audio TW400Ti-Nd-4 SLIM Super Tweeter offers a smooth response and extremely high efficiency from high mid range through high range frequencies. This compact tweeter is part of a wide family from the TW400Ti-Nd Series, featuring a strong neodymium motor which increases its efficiency and lowers its weight ans size dramatically without compromising any performance. Highlights Designed to fit in tight spaces without any major modificationsTitanium diaphragm for an accurate and detailed responseDesigned to add high output, high frequency response to any interior systemHidden push terminal connection, takes less space on installationBuilt-in capacitors act as a crossover and attenuates the low frequencies for smooth frequency responseAble to take a ton of power! Up to 120 watts RMS of power handling are on tap with a 12 dB/octave crossover at 6,000 HzSold in Pairs – Mounting Screws are included, Also available in White After several months of research and development, we were able to obtain a high level of output from this neodymium motor and an unique diaphragm design for the TW400Ti-Nd Series. Featuring a new concept, easy to replace diaphragm ( solderless ) makes a very easy task to fix your tweeter in few minutes.GENERAL SPECIFICATIONS Nominal impedance 4 Ohms Nominal Power Handling* 60 Watts each Continuous Program Power (RMS)** 120 Watts each Max Peak Power*** 240 Watts each Sensitivity 2.00V at 1m 105 dB Recommended High Pass Crossover For Full Power Handling 6000 Hz 12db/oct Crossover Frequency Response at -10dB 4,500 – 20,000Hz Voice Coil Diameter 1.0″ (25 mm) Voice Coil Wire CCAW Voice Coil Former Material Kapton Diaphragm Material Titanium Flux Density 1.45 T Magnet Material Neodymium *Nominal power handling is defined as the maximum RMS power that the speaker can handle in a 2-hour test with a pink noise with 6dB of crest factor and a bandpass filter with 12db/oct tuned in its usable frequency range. **Continuous Program Power (RMS) is the maximum power that the speaker can handle considering a regular musical program using our recommended filters, this power can be used to define the optimum amplifier power to avoid a clean signal without clipping or saturation. ***Max Peak Power is the maximum power operation for the speaker, this power is allowed just for a few fractions of a second, usually found just on the peaks of the music. Keeping this power for a little longer timer will damage the speaker. EXTRA INFO Overall Depth 1.61″ (41 mm) Mounting Depth 1.22″ (31 mm) Overall Diameter 2.92″ (74 mm) Cutout Diameter 2.27″ (57.7 mm) Net Weight 0.66 lbs (0.30 kg) Shipping Weight (pair) 1.54 lbs (0.70 kg) Carton Dimensions W x L x H 6.77″ x 3.15″ x 1.99″ (172 x 80 x 50 mm)

Weiterlesen2x PRV 240W Shallow Super Tweeter Neodymium TW400Ti-Nd-4 SLIM 4 Ohm 3″ Rounded

4x PRV 2″ Horn Driver WG2000Py SLIM Shallow Mount High Frequency 8 Ohm 600 Watts

  • Beitrags-Autor:
  • Beitrags-Kategorie:
  • Beitrags-Kommentare:0 Kommentare

INCLUDES: 4x PRV WG2000Py SLIM Mids & Highs Compression Horn driver for Car Audio - 600 Watts Package - 150 Watts each horn driver FEATURES: The WG2000Py SLIM is a Shallow mount 2″ horn driver featuring a Polyimide Pro Audio Compression Driver with a 2” exit WGP14-50X Slim Waveguide. This is a top-of-the-line horn driver designed to offer unsurpassed natural upper midrange and high frequency response at high sensitivity, with crystal clear natural sound from the Polyimide diaphragm.Polyimide diaphragm with large 2.0″ Voice Coil, providing dynamic output along with excellent efficiency – 107 dB SensitivityMids & Highs 2″ Exit Driver + Shallow Horn WGP14-50X – Perfect as compression driver for car audioCrystal clear natural sound with wider response from 1000 to 17,000 HzPRO Audio horn driver, able to handle 150 Watts Continuous Program Power (RMS) with musicCompact driver mounted on slim horn, ideal for tight spaces, increase sound output on your system with this slim solution. Great choice for custom car audio door panelsThe driver’s small diameter allows front mounting, making it easy to install without detaching the driver from the WGP14-50X Horn.Its design was developed to give custom doors a new solution for a shallow horn driver, its 2.0” voice coil allows it to push more power into it, increasing its output tremendously because of its low mass diaphragm.The specially designed Polyimide diaphragm provides durability and additional damping for natural sound quality. This technology raises the bar for high frequency drivers by giving the driver wider usable bandwidth for smooth, dynamic output along with excellent efficiency.The Polyimide diaphragms supersede titanium diaphragms, being able to play low frequencies without shattering and performing more accurately at high frequencies.PRV Audio WG2000Py SLIM Shallow Mount 2″ Exit Mids & Highs Horn Driver 150 Watts 8 Ohm – Compression Horn driver for Car AudioGENERAL SPECIFICATIONSExit Throat Diameter2” (50 mm)Nominal impedance8 OhmNominal Power Handling75 WattsContinuous Program Power (RMS)**150 WattsPeak Power300 WattsSensitivity 2.83V at 1m107 dBRecommended Hi Pass Crossover For Full Power Handling1000 Hz 12db Per Octave CrossoverFrequency Response at -10dB1000 – 17,000 HzVoice Coil Diameter2”(51 mm)Voice Coil WireCCAWVoice Coil Former MaterialKaptonDiaphragm MaterialPolyimideFlux Density2.10 TMagnet MaterialFerrite EXTRA INFOOverall Depth5.87” (149 mm)Mounting Depth5.55” (141 mm)Overall Width6.14″ (156 mm)Overall Height6.14″ (156 mm)Baffle Cutout5.75″(146 mm)Net Weight6.45 lbs (2.94 kg)Shipping Weight7.05 lbs (3.20 kg)Carton Dimensions W x L x H6.89” x 6.89” x 7.48” (175x 175 x 190mm)

Weiterlesen4x PRV 2″ Horn Driver WG2000Py SLIM Shallow Mount High Frequency 8 Ohm 600 Watts

4x PRV Audio TW700Ti Bullet 4” Pro Audio Super Tweeters 8 Ohms Titanium 960W

  • Beitrags-Autor:
  • Beitrags-Kategorie:
  • Beitrags-Kommentare:0 Kommentare

INCLUDES: 4x PRV Audio TW700Ti Pro Audio Super Tweeters 8 Ohm - 960 Watts Package - 240 Watts each tweeter FEATURES: Add detail to any speaker with PRV Audio’s TW700Ti BLACK titanium bullet super tweeter! With high frequency response up to 20,000 Hz and a sensitivity of 107 dB at 1W/1m, the TW700Ti Series PRO Audio Tweeter can keep up with even the most demanding speaker systems.A square faceplate makes it easier to install, made from a strong aluminum horn, which offers a smooth response and extremely high efficiency, enabling it to cover a wide frequency range and offer a smooth response.4″ Square PRO Audio Super Tweeter – Built to Perform to add high output, high frequency response to large output systemsHigh Temperature 1.5″ diameter voice coil capable of handling up to 240 Watts musical program power up to 240 Watts of amplifier RMS powerDesigned for high frequency reproduction at a high SPL level with low distortion thanks to its large motor.The built-in capacitor acts as a crossover and attenuates the low frequencies for smooth frequency response.Available in White and Chrome Finish!Enhancing its versatility, the flat sides of the tweeter allow for seamless side-by-side mounting, ensuring efficient use of space.The incorporation of an oversized magnet system further amplifies the magnetic field within the gap, resulting in heightened sensitivity and minimal distortion, thereby optimizing overall sound quality.A capacitor is included for protection from damaging frequencies at high power. Mounting hardware included.Not only does this PRO audio bullet tweeter look as good as it sounds it is also able to take a huge amount of power due to its 1.5″ diameter copper voice coil. Up to 240 watts of musical program power are on tap to keep up with the most demanding professional audio, high output home audio, and high SPL car audio systems.Recommended Settings with DSP/CrossoverWe strongly recommended ALWAYS to use a high pass filter ( HPF ) on or to the amplifier channel that will be running the tweeters.If you have just a high output crossover such as: EX3.5 STEREO or EX4.6 PRO – Use the HIGH OUT channel to feed the amplifier input with a HPF set to:At 5000Hz – if you are running just a speaker and tweeter setup At 8000Hz – If you are running a 3-Way system ( speaker, phenolic driver and tweeter )If you are taking your system to the next level and tuning it with a digital signal processor: DSP 2.4X or DSP 2.8X – Set on the channel to feed the amplifier input with a HPF set to:At 5000Hz at LR18 – if you are running just a speaker and tweeter setupAt 7000Hz at LR24 – If you are running a 3-Way system ( speaker, phenolic driver and tweeter ) GENERAL SPECIFICATIONSNominal impedance8 OhmNominal Power Handling120 WattsContinuous Program Power (RMS)240 WattsMax Peak Power480 WattsSensitivity 2.83V at 1m107 dBRecommended Hi Pass Crossover****For Full Power Handling5000 Hz****12db Per Octave CrossoverFrequency Response at -10dB3,500 – 20,000 HzVoice Coil Diameter1.5”(38 mm)Voice Coil WireCCAWVoice Coil Former MaterialKaptonDiaphragm MaterialTitaniumFlux Density1.60 TMagnet MaterialFerriteEXTRA INFOOverall Depth2.97” (75.54 mm)Mounting Depth2.55” (64.9 mm)Overall Width4.05” (103 mm)Overall Height4.05” (103 mm)Cutout Diameter3.58” (91 mm)Net Weight3.58 lbs (1.58 kg)Shipping Weight3.62 lbs (1.64 kg)Carton Dimensions W x L x H4.5” x 4.5” x 3.25”(114 x 114 x 82.5 mm)

Weiterlesen4x PRV Audio TW700Ti Bullet 4” Pro Audio Super Tweeters 8 Ohms Titanium 960W

2x PRV Audio TW700Ti Bullet 4” Pro Audio Super Tweeters 8 Ohms Titanium 480W

  • Beitrags-Autor:
  • Beitrags-Kategorie:
  • Beitrags-Kommentare:0 Kommentare

INCLUDES: 2x PRV Audio TW700Ti Pro Audio Super Tweeters 8 Ohm - 480 Watts Package - 240 Watts each tweeter FEATURES: Add detail to any speaker with PRV Audio’s TW700Ti BLACK titanium bullet super tweeter! With high frequency response up to 20,000 Hz and a sensitivity of 107 dB at 1W/1m, the TW700Ti Series PRO Audio Tweeter can keep up with even the most demanding speaker systems.A square faceplate makes it easier to install, made from a strong aluminum horn, which offers a smooth response and extremely high efficiency, enabling it to cover a wide frequency range and offer a smooth response.4″ Square PRO Audio Super Tweeter – Built to Perform to add high output, high frequency response to large output systemsHigh Temperature 1.5″ diameter voice coil capable of handling up to 240 Watts musical program power up to 240 Watts of amplifier RMS powerDesigned for high frequency reproduction at a high SPL level with low distortion thanks to its large motor.The built-in capacitor acts as a crossover and attenuates the low frequencies for smooth frequency response.Available in White and Chrome Finish!Enhancing its versatility, the flat sides of the tweeter allow for seamless side-by-side mounting, ensuring efficient use of space.The incorporation of an oversized magnet system further amplifies the magnetic field within the gap, resulting in heightened sensitivity and minimal distortion, thereby optimizing overall sound quality.A capacitor is included for protection from damaging frequencies at high power. Mounting hardware included.Not only does this PRO audio bullet tweeter look as good as it sounds it is also able to take a huge amount of power due to its 1.5″ diameter copper voice coil. Up to 240 watts of musical program power are on tap to keep up with the most demanding professional audio, high output home audio, and high SPL car audio systems.Recommended Settings with DSP/CrossoverWe strongly recommended ALWAYS to use a high pass filter ( HPF ) on or to the amplifier channel that will be running the tweeters.If you have just a high output crossover such as: EX3.5 STEREO or EX4.6 PRO – Use the HIGH OUT channel to feed the amplifier input with a HPF set to:At 5000Hz – if you are running just a speaker and tweeter setup At 8000Hz – If you are running a 3-Way system ( speaker, phenolic driver and tweeter )If you are taking your system to the next level and tuning it with a digital signal processor: DSP 2.4X or DSP 2.8X – Set on the channel to feed the amplifier input with a HPF set to:At 5000Hz at LR18 – if you are running just a speaker and tweeter setupAt 7000Hz at LR24 – If you are running a 3-Way system ( speaker, phenolic driver and tweeter ) GENERAL SPECIFICATIONSNominal impedance8 OhmNominal Power Handling120 WattsContinuous Program Power (RMS)240 WattsMax Peak Power480 WattsSensitivity 2.83V at 1m107 dBRecommended Hi Pass Crossover****For Full Power Handling5000 Hz****12db Per Octave CrossoverFrequency Response at -10dB3,500 – 20,000 HzVoice Coil Diameter1.5”(38 mm)Voice Coil WireCCAWVoice Coil Former MaterialKaptonDiaphragm MaterialTitaniumFlux Density1.60 TMagnet MaterialFerriteEXTRA INFOOverall Depth2.97” (75.54 mm)Mounting Depth2.55” (64.9 mm)Overall Width4.05” (103 mm)Overall Height4.05” (103 mm)Cutout Diameter3.58” (91 mm)Net Weight3.58 lbs (1.58 kg)Shipping Weight3.62 lbs (1.64 kg)Carton Dimensions W x L x H4.5” x 4.5” x 3.25”(114 x 114 x 82.5 mm)

Weiterlesen2x PRV Audio TW700Ti Bullet 4” Pro Audio Super Tweeters 8 Ohms Titanium 480W

2x PRV Audio Midrange 12″ Speakers 8 Ohm 12MR PRO 350 Watts RMS Each

  • Beitrags-Autor:
  • Beitrags-Kategorie:
  • Beitrags-Kommentare:0 Kommentare

The PRV Audio Midrange 12" Speakers are powerful 8 Ohm woofers designed for mid-range frequencies, perfect for musical instruments and audio equipment. With a weight of 25.4lbs and a depth of 5.91 inches, these speakers are reliable and durable. The bundle includes two 350 Watts RMS speakers from the trusted brand PRV Audio, ensuring high-quality sound for your audio setup. Made in Brazil, these speakers are compatible with various brands and models, making them a versatile option for enhancing your audio experience.

Weiterlesen2x PRV Audio Midrange 12″ Speakers 8 Ohm 12MR PRO 350 Watts RMS Each